SanDisk Cruzer Blade sur Ubuntu 16.04
J'ai une clé USB 128G mais Ubuntu ne la monte pas, ne voit pas ses partitions et ne me laisse pas la formater.
dmesg:
[ 3124.001070] scsi Host8: usb-storage 3-6:1.0
[ 3125.001042] scsi 8:0:0:0: Direct-Access SanDisk Cruzer Blade 1.27 PQ: 0 ANSI: 6
[ 3125.001511] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 3125.002864] sd 8:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[ 3125.004512] sd 8:0:0:0: [sdb] Write Protect is off
[ 3125.004516] sd 8:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3125.004788] sd 8:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3155.886694] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3186.917281] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3217.963891] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3248.930474] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3259.170022] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3275.409403] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3275.649387] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3285.888788] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3286.017438] sd 8:0:0:0: Device offlined - not ready after error recovery
[ 3286.017447] sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 3286.017450] sd 8:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 3286.017452] blk_update_request: I/O error, dev sdb, sector 0
[ 3286.017455] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3286.017491] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017499] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017502] ldm_validate_partition_table(): Disk read failed.
[ 3286.017505] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017509] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017512] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017516] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017518] Dev sdb: unable to read RDB block 0
[ 3286.017521] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017525] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017533] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017537] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017540] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017542] sdb: unable to read partition table
[ 3286.017654] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 3507.045052] usb 3-6: USB disconnect, device number 9
[ 3532.849931] usb 3-6: new high-speed USB device number 10 using xhci_hcd
[ 3534.530519] usb 3-6: New USB device found, idVendor=0781, idProduct=5567
[ 3534.530525] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3534.530528] usb 3-6: Product: Cruzer Blade
[ 3534.530530] usb 3-6: Manufacturer: SanDisk
[ 3534.530532] usb 3-6: SerialNumber: 4C530000360119115540
[ 3534.531122] usb-storage 3-6:1.0: USB Mass Storage device detected
[ 3534.532419] scsi Host9: usb-storage 3-6:1.0
[ 3535.530816] scsi 9:0:0:0: Direct-Access SanDisk Cruzer Blade 1.27 PQ: 0 ANSI: 6
[ 3535.531338] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 3535.532651] sd 9:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[ 3535.534275] sd 9:0:0:0: [sdb] Write Protect is off
[ 3535.534282] sd 9:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3535.534600] sd 9:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
dmesg sur un port USB2:
[13712.795990] usb 3-6: new high-speed USB device number 16 using xhci_hcd
[13714.424628] usb 3-6: New USB device found, idVendor=0781, idProduct=5567
[13714.424632] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[13714.424634] usb 3-6: Product: Cruzer Blade
[13714.424636] usb 3-6: Manufacturer: SanDisk
[13714.424637] usb 3-6: SerialNumber: 4C530000360119115540
[13714.425386] usb-storage 3-6:1.0: USB Mass Storage device detected
[13714.425523] scsi Host10: usb-storage 3-6:1.0
[13715.425303] scsi 10:0:0:0: Direct-Access SanDisk Cruzer Blade 1.27 PQ: 0 ANSI: 6
[13715.425690] sd 10:0:0:0: Attached scsi generic sg2 type 0
[13715.427008] sd 10:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[13715.428665] sd 10:0:0:0: [sdb] Write Protect is off
[13715.428668] sd 10:0:0:0: [sdb] Mode Sense: 43 00 00 00
[13715.428953] sd 10:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[13746.221203] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13777.190106] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13808.175044] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13839.208027] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13849.452206] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13865.692838] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13865.988708] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13876.229026] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13876.357892] sd 10:0:0:0: Device offlined - not ready after error recovery
[13876.357912] sd 10:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[13876.357919] sd 10:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[13876.357924] blk_update_request: I/O error, dev sdb, sector 0
[13876.357931] Buffer I/O error on dev sdb, logical block 0, async page read
[13876.358015] sd 10:0:0:0: rejecting I/O to offline device
[13876.358042] sd 10:0:0:0: rejecting I/O to offline device
[13876.358049] ldm_validate_partition_table(): Disk read failed.
[13876.358059] sd 10:0:0:0: rejecting I/O to offline device
[13876.358069] sd 10:0:0:0: rejecting I/O to offline device
[13876.358080] sd 10:0:0:0: rejecting I/O to offline device
[13876.358090] sd 10:0:0:0: rejecting I/O to offline device
[13876.358097] Dev sdb: unable to read RDB block 0
[13876.358105] sd 10:0:0:0: rejecting I/O to offline device
[13876.358116] sd 10:0:0:0: rejecting I/O to offline device
[13876.358136] sd 10:0:0:0: rejecting I/O to offline device
[13876.358147] sd 10:0:0:0: rejecting I/O to offline device
[13876.358158] sd 10:0:0:0: rejecting I/O to offline device
[13876.358163] sdb: unable to read partition table
[13876.358568] sd 10:0:0:0: [sdb] Attached SCSI removable disk
fsck:
sela@sela-ThinkPad-T440p:~$ Sudo fsck -n /dev/sd
/dev/sda /dev/sda1 /dev/sda2 /dev/sda5 /dev/sdb
sela@sela-ThinkPad-T440p:~$ Sudo fsck -n /dev/sdb
fsck from util-linux 2.27.1
e2fsck 1.42.13 (17-May-2015)
fsck.ext2: No such device or address while trying to open /dev/sdb
Possibly non-existent or swap device?
lsusb:
sela@sela-ThinkPad-T440p:~$ lsusb
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 138a:0017 Validity Sensors, Inc. Fingerprint Reader
Bus 003 Device 010: ID 0781:5567 SanDisk Corp. Cruzer Blade
Bus 003 Device 002: ID 058f:9540 Alcor Micro Corp. AU9540 Smartcard Reader
Bus 003 Device 006: ID 04f2:b39a Chicony Electronics Co., Ltd
Bus 003 Device 004: ID 0bdb:193e Ericsson Business Mobile Networks BV
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Essayer de formater quand même:
sela@sela-ThinkPad-T440p:~$ Sudo mkfs.fat /dev/sdb -I
mkfs.fat 3.0.28 (2015-05-16)
/dev/sdb: No such device or address
Impossible de trouver une solution. Toute aide serait appréciée.
Edit: Dans l'application Disks, j'ai trouvé ceci:
Une autre chose que j'ai essayé:
sela@sela-ThinkPad-T440p:~$ Sudo tune2fs -l /dev/sdb
tune2fs 1.42.13 (17-May-2015)
tune2fs: No such device or address while trying to open /dev/sdb
Couldn't find valid filesystem superblock.
Une autre chose que j'ai essayée est de changer l'état de l'appareil et de le formater:
sela@sela-ThinkPad-T440p:~$ Sudo -s
root@sela-ThinkPad-T440p:~# cat /sys/bus/scsi/devices/7\:0\:0\:0/state
offline
root@sela-ThinkPad-T440p:~# echo running > /sys/bus/scsi/devices/7\:0\:0\:0/state
root@sela-ThinkPad-T440p:~# cat /sys/bus/scsi/devices/7\:0\:0\:0/state
running
root@sela-ThinkPad-T440p:~# mkdosfs -v -n 'SELA111' -I /dev/sdb
sdb
root@sela-ThinkPad-T440p:~# mkdosfs -v -n 'SELA111' -I /dev/sdb
mkfs.fat 3.0.28 (2015-05-16)
/dev/sdb: No medium found
root@sela-ThinkPad-T440p:~#
Cette trace de pile est-elle liée?
[ 6478.677549] usb 3-6: reset high-speed USB device number 15 using xhci_hcd
[ 6480.129365] INFO: task kworker/u16:4:4979 blocked for more than 120 seconds.
[ 6480.129369] Not tainted 4.4.0-24-generic #43-Ubuntu
[ 6480.129370] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 6480.129372] kworker/u16:4 D ffff8804033a3848 0 4979 2 0x00000000
[ 6480.129380] Workqueue: events_unbound async_run_entry_fn
[ 6480.129381] ffff8804033a3848 ffff8804261f6a80 ffff88042c2d5280 ffff880425003700
[ 6480.129383] ffff8804033a4000 ffff88043e396d00 7fffffffffffffff ffffffff81822310
[ 6480.129385] ffff8804033a39a8 ffff8804033a3860 ffffffff81821b15 0000000000000000
[ 6480.129387] Call Trace:
[ 6480.129392] [<ffffffff81822310>] ? bit_wait+0x60/0x60
[ 6480.129395] [<ffffffff81821b15>] schedule+0x35/0x80
[ 6480.129397] [<ffffffff81824c35>] schedule_timeout+0x1b5/0x270
[ 6480.129401] [<ffffffff813bb526>] ? submit_bio+0x76/0x170
[ 6480.129403] [<ffffffff81822310>] ? bit_wait+0x60/0x60
[ 6480.129405] [<ffffffff81821044>] io_schedule_timeout+0xa4/0x110
[ 6480.129407] [<ffffffff8182232b>] bit_wait_io+0x1b/0x70
[ 6480.129409] [<ffffffff81821ebd>] __wait_on_bit+0x5d/0x90
[ 6480.129413] [<ffffffff812481d0>] ? blkdev_readpages+0x20/0x20
[ 6480.129416] [<ffffffff8118cd0b>] wait_on_page_bit+0xcb/0xf0
[ 6480.129421] [<ffffffff810c3bc0>] ? autoremove_wake_function+0x40/0x40
[ 6480.129423] [<ffffffff8118cf39>] wait_on_page_read+0x49/0x50
[ 6480.129426] [<ffffffff8118e56d>] do_read_cache_page+0x8d/0x1b0
[ 6480.129428] [<ffffffff8118e6a9>] read_cache_page+0x19/0x20
[ 6480.129430] [<ffffffff813ce77d>] read_dev_sector+0x2d/0x90
[ 6480.129433] [<ffffffff813d51fd>] read_lba+0x14d/0x210
[ 6480.129435] [<ffffffff813d5ab2>] efi_partition+0xf2/0x7d0
[ 6480.129438] [<ffffffff813f4ffb>] ? string.isra.4+0x3b/0xd0
[ 6480.129440] [<ffffffff813f6f39>] ? snprintf+0x49/0x60
[ 6480.129442] [<ffffffff813d59c0>] ? compare_gpts+0x280/0x280
[ 6480.129443] [<ffffffff813cfb2e>] check_partition+0x13e/0x220
[ 6480.129445] [<ffffffff813cf060>] rescan_partitions+0xc0/0x2b0
[ 6480.129447] [<ffffffff812490cd>] __blkdev_get+0x30d/0x460
[ 6480.129449] [<ffffffff8124968d>] blkdev_get+0x12d/0x340
[ 6480.129453] [<ffffffff812274f9>] ? unlock_new_inode+0x49/0x80
[ 6480.129455] [<ffffffff81248068>] ? bdget+0x118/0x130
[ 6480.129459] [<ffffffff813ccb13>] add_disk+0x403/0x490
[ 6480.129463] [<ffffffff815592a1>] ? update_autosuspend+0x51/0x60
[ 6480.129465] [<ffffffff8155936c>] ? __pm_runtime_use_autosuspend+0x5c/0x80
[ 6480.129469] [<ffffffff815c0845>] sd_probe_async+0x115/0x1d0
[ 6480.129471] [<ffffffff810a30a8>] async_run_entry_fn+0x48/0x150
[ 6480.129474] [<ffffffff8109a175>] process_one_work+0x165/0x480
[ 6480.129476] [<ffffffff8109a4db>] worker_thread+0x4b/0x4c0
[ 6480.129477] [<ffffffff8109a490>] ? process_one_work+0x480/0x480
[ 6480.129479] [<ffffffff8109a490>] ? process_one_work+0x480/0x480
[ 6480.129481] [<ffffffff810a06a8>] kthread+0xd8/0xf0
[ 6480.129483] [<ffffffff810a05d0>] ? kthread_create_on_node+0x1e0/0x1e0
[ 6480.129484] [<ffffffff81825f8f>] ret_from_fork+0x3f/0x70
[ 6480.129486] [<ffffffff810a05d0>] ? kthread_create_on_node+0x1e0/0x1e0
[ 6488.917955] usb 3-6: reset high-speed USB device number 15 using xhci_hcd
Pour certaines raisons, ce périphérique est supprimé soudainement par le noyau ou le contrôleur USB de manière non propre, il laisse donc ces /dev nœuds artefact.
C'est un périphérique USB2!
Comme je vois les données de spécification de SanDisk Cruzer Blade .:
Capacity 128 GB 64 GB 32 GB 16 GB 8 GB 4 GB
Generation USB 2.0 USB 2.0 USB 2.0 USB 2.0 USB 2.0 USB 2.0
Il doit s'agir d'un périphérique USB2. Il pourrait donc être buggé avec le port USB3
usb 3-6: reset high-speed USB device number 9 using xhci_hcd
...
usb 3-6: new high-speed USB device number 10 using xhci_hcd
Modifiez-le sur un autre port USB2, votre ordinateur portable devrait déjà avoir 2 ports ( spécification Lenovo ThinkPad T440p ).
Il est clair que xhci_hcd l'a détecté en tant que périphérique USB2 à partir de sa description
usb 3-6: nouveau haut débit périphérique USB numéro 10 utilisant xhci_hcd
Les périphériques USB3 devraient obtenir super-speed ou super-speed+. Référence: Wikipedia: USB, Historique des versions
Option 1. Désactiver USB3 du BIOS
C'est manuel mentionne:
- 2 côté gauche, comme USB3
- 2 côté droit, comme USB (? S'il a
+signe qu'il s'agit d'un port USB2) Le BIOS a la possibilité de désactiver USB3 sur les 2 ports partagés entre USB2 et USB3. Quel côté? Je ne sais pas!
Il se peut donc que les ports partagés soient ceux du côté droit. Désactivez l'USB3 dans le BIOS et voyez quelles sont les nouvelles sorties de
dmesgdes deux côtés, plus la sortie delsusb.
Option 2. Mettre à niveau le BIOS/UEFI
Il y a une nouvelle version:
Taille de l'utilitaire de mise à jour du BIOS: 5,7 Mo 2,37 28/04/2016
La note de publication mentionne les problèmes USB comptés, le plus intéressant est celui-ci:
<2.19> UEFI: 2.19 / ECP: 1.08 - (Fix) Fixed an issue that might fail to boot the computer remotely. - (Fix) Fixed an issue where USB 3.0 device detection might fail when the device was attached via the USB 3.0 Hub and the USB 3.0 Mode option was set to Enabled in ThinkPad Setup.